Disclaimer: This is an example of a student written essay.
Click here for sample essays written by our professional writers.

Any scientific information contained within this essay should not be treated as fact, this content is to be used for educational purposes only and may contain factual inaccuracies or be out of date.

Pneumatic Auto Gear Changer Project

Paper Type: Free Essay Subject: Engineering
Wordcount: 1644 words Published: 31st Aug 2017

Reference this

(a) Introduction

1.1 This career episode is based on my design and fabrication project carried out during the penultimate year of my bachelor’s degree in Mechanical Engineering at Rajiv Gandhi College of Engineering (Anna University Affiliated)-Sriperumbudur, Tamil Nadu state, India. Established in 2001, it is a self-financed and one of the best engineering institutes in Tamil Nadu. The project was completed over a period of 3 months from December 2012 to March, 2013.

(b) Background

1.2 The project on “Pneumatic Auto Gear Changer” was carried out in order to understand and implement theories in gear change application. Its purpose was to analyze the various steps involved and to provide recommendations for a real world use of this technology. I carried out this project as a part of a group of four people. In this project, a push button was used to activate/deactivate a solenoid valve and at the time of gear changing, the switch was triggered and the solenoid valve was activated. This in turn causes the compressed air to go through the pneumatic cylinder. The compressed air pushes the pneumatic cylinder as it passes through a tube and henceforth changes the gear from one speed to the other with the help of a gear box arrangement.

1.3 The automatic gear changing structure is relatively useful in low cost automation in all automobiles. Pneumatic systems work at higher speeds and the manpower requirement is reduced due to this project. The design and the implementation of this project in the real world application was made and a detailed report was submitted.

This project work was supervised under Mr. Manoj Kumar, the associate professor in the department of mechanical engineering at Rajiv Gandhi College of Engineering. As it was an open ended project, I had to look up through several online journals, document reviews and also took guidance from the head of the department on various projects and ideas. The project time was quite limited and had to be come up with a proper design plan before the actual start of the project. This proved to be quite a challenging task as this was the first real world project in my career. However, I was completely aware of the fact that, these would be the kind of challenges and problems I would face in real life as a professional engineer.

Some of the duties I was involved in during the course of this project were as follows:

  • I carried out an extensive study on various materials relating to the pneumatic systems.
  • Since, there was no specific consensus on the selection of compressors, I had to select the one that best suited the requirements of the project while considering all the technical aspects.
  • I also dealt with the equipment suppliers on behalf of my team to purchase the necessary materials needed for the project.
  • I attended meetings with my supervisor to discuss individual observation and the progress of the project.
  • I presented this project to the department faculties and also completed an extensive project report.

(c) Personal Engineering Activity

As a first step of the project, I explained my thoughts on doing this project to my supervisor. I carried out my research regarding the project and presented him the importance of the project before carrying out the project.  The present scenario gear changer plays a vital role in automobiles.  Manual transmissions have become uncommon in many cases of cars sold across Australia, North America and some parts of Asia. However, they remain dominant in parts of Europe and other developing countries. Hence, I did an analysis on the present day vehicles equipped with automatic transmission option and those that are not and further highlighted the importance of the project in the present and future of automobiles as well as in certain machineries.

After deciding on the project, I carried out numerous literature reviews in order to come up with an appropriate design plan and to acquire the necessary equipment needed for the project. However, the articles and writings published on the topic was quite limited and were available for only specific cases.  As my project was regarding the project pneumatic gear changer, I did my extensive research on the pneumatic side of the project. Furthermore, I reviewed the advantages of pneumatic system and discussed with my supervisor for the usability in the project. Pneumatic system and was best considered due to its following reasons:

  • The pneumatic system power output could be easily controlled
  • Over loading does not affect the pneumatic systems
  • The pneumatic system could be used at varying working temperatures
  • Transportation of air through pipelines over long distances can be easily done with pneumatics in place.
  • Pneumatics enables high working speeds
  • It is a system which requires minimal upkeep.

In this project, I used a reciprocating compressor as the key component for the supply of compressed air. I selected the appropriate equipment for the project after evaluating the suitability of information acquired from several sources. A compressor is an instrument that sucks in air and gas at an optimum pressure and deliverers the air back at a higher pressure as the output. It was very important for my project to select the appropriate compressor as pneumatic systems operate primarily on the supply of both compressed air and pressure into the system. Moreover, I had to make sure, clean conditions were maintained during the phase of the project as warm and moist air could result in precipitation of condense from the compressed air. The following is the schematic diagram of pneumatic auto gear changer used in this project.

Figure 1: Schematic diagram of pneumatic auto gear changer

I also considered an important element for this project which was the push button. The push button switch was fixed near the driving seat of the vehicle. Besides this, I had set up an air tank with fully filled compressed air in it. Prior to gear changing, the solenoid valve was activated by triggering the switch. The compressed air streamed from the air tank to the pneumatic cylinder as the solenoid valve was open. Likewise, at the time of compressed air inlet into the cylinder, the pneumatic cylinder moved forward and the gear box liver moved along automatically from one position to the next. The gear box liver was further activated which allowed the vehicle running at different speeds. I have highlighted the advantages of this type to my supervisor and was duly approved and appreciated by him. They are as follows:

It required simple maintenance cares

  • A safe system for the automobile.
  • Easy to Handle.
  • Low cost automation project
  • Repairing was easy.
  • Easy replacement.

However, some of the disadvantages of this type were as follows:

  • Initial cost was high.
  • The system was a complicated one.
  • During the course of this project, I used a control valve to control the flow direction within the system. I also used a 3/2 single acting solenoid valve, having one inlet, outlet and an exhaust port. The air entered the pneumatic single acting solenoid valve once the push button was activated. Moreover, I introduced a pneumatic shifter to the whole design as it works through compressed air power. So once the gear changing signals were received, the pneumatic shifter opens or closes the magnetic valve assembly. The compressed air flows into the system once these valves are open, or thrusts it out thereby creating the effect of shifting gear mechanism. More compressed air into the system allowed the gear to be shifted up and the gear shifted down as the air was let. Furthermore, I used an on-board tank to get this compressed air to the cylinder even though I knew re-routing the engine exhaust could be a possibility and be economically viable however, it would result in lower performance as most of the oxygen present in the exhaust gas would already be burnt.

Figure 2: Schematic of a 3/2 single acting solenoid valve

  • After the analysis on various aspects of this project, I discussed my project outcomes and my results.  Putting all the information to use, I wrote the final report titled “Pneumatic Auto Gear Changer “and presented this to my department professors and to the head of the department.

(d) Summary

This project presented me with the opportunity to understand the applications of theoretical knowledge that I had acquired in class rooms to implement in a real world project.  Discussions during the project with the supervisor provided great insight to challenges presented throughout the project.  The challenges uncovered were resolved by use of appropriate technical skills. This project also helped me understand the working and execution of any engineering project and served as a stepping stone to the real world. Overall, I am very happy that I could contribute myself effectively to this project at its various stages and also helped to secure the highest possible grade for this project.


Cite This Work

To export a reference to this article please select a referencing stye below:

Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.

Related Services

View all

DMCA / Removal Request

If you are the original writer of this essay and no longer wish to have your work published on UKEssays.com then please: